New Here with a Turbo Jeep

[Escape]

Hey Everyone.

Met up with Brian (BJB) today to get a SRT8 Hitch and he gave me a card and said come on over...so without any further delay here is my new member intro with build specs and some pics of what I've been working on.

A Few Go Fast Goodies...

Fully Forged Engine from SharaDon Performance
- 6.1 Forged Performance Crank (Custom Ground)
- Eagle ESP 4340 H-Beam Rods
- 6.1 Forged Pushrods
- Custom Diamond Blower Pistons rings/pins coating skirt and ceramic top. All the goodies 9:1 compression
- ATI SuperDamper
- ARP Studs, head and main
- 6.1 oil pump
- Timing set
- Cam bearings
- 6.1 cam
- Manley valve springs for cam
- Bored & Honed Custom 2003 5.7 HEMI Ram block with tq plate
- Check line bore
- True & square block
- Balanced assembly (to the 100th of a gram)
- Main and rod bearings
- Head gaskets
- Exhaust gaskets
- Rear main seal
- Hot tank block
- Blue print shortblock
- File fit rings
- Clean original parts to go onto new shortblock
- Oil prime engine with brake in oil
- Painted Jet Black
- MDS retained and functional for an awesome 12 MPG :hehe3: :thumbsup:

Transmission
- 2800 stall Edge Racing Torque Converter

Forced Induction from North Coast Turbo Systems
- Single T4/T4 T-70 Turbocharger
- 60mm Wastegate
- 50mm BOV
- All mandrel bent 304H SS tubing (both hot and cold side)
- Shielded Air intake system
- Complete exhaust system from the factory cats back to the polished SS exhaust tips (factory cats retained)
- Bosch thread, wide band O2 sensor bung and plug installed
- Stainless Steel “T-Bar” clamps
- 4 ply 100% silicone connectors
- 8 new EV14 fuel injectors, 56 lb
- Progressive Water/Methanol injection system tied into washer tank with LED on signal and factory EVIC alert when low.
- All bronze spur gear rotary pump with Stainless Steel shafts oil return system

Engine Management - To make it all run
- iEMS3 Integrated Engine Management System 3

Look good mods...cause if your going to go fast you have to look good doing it! :thumbsup:

- 2006 Front SRT8 Bumper
- 2006 Side SRT8 Rocker Moldings
- 2006 Rear SRT8 Bumper
- 2006 SRT8 Grille
- Gibson resonators and 4" dual tips
- Whistler Mod with 10K LED Flashtech Halo's
- RamMedic CF Hood
- SRT8 Hitch (from BJB)
- Cheapo 5 dollar rubber antenna (well it beats having that 30" fishing pole on there :ROTFLMAO: )

- Removal of Stock Badges except Jeep on the back
- Custom Turned Billet XRT8 Emblems and Annodized Black Laser Engraved Hemi Punisher Emblem(back)
- Custom Turned Billet Punisher Skulls (2 sides 1 rear)
Pics as soon as I get them!

Rolling on...

Summer setup
- 2008 Alcoa Forged SRT8 20x9/20x10 currently wrapped in the stock Goodyears (soon to be changed :thumbsup:)

Winter setup
- Rims - 17" Stock Ronin II
- Tires - BFG All-Terrain TA KO LT265/65R17E 120S

Gauges & Monitoring - To keep an eye on it all
- Diablo Trinity (working on a key cycle issue)
- MSD DashHawk
- Boost = Auto Meter 3376
- A/F Wideband = AEM UEGO 30-4100
- EGT = Auto Meter 6345
- Triple A-Pillar Pod = S.A.M. RGPML600 - from http://www.samsteffansson.se/samindex.html

Future mods...
- SharaDon Stage 3 545RFE Trans
- Return fuel system (using a Aeromotive HP Marine USCG Fuel Pump, P/N 11108)
- Brembo Big Brake setup to stop this thing :lulz:
- Turn up the boost to 20psi and see what needs replaced! :nuts:
- I'm sure there is something else...cause it can never be finished :ROTFLMAO:

And some pics as promised!

When it came home.
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_4408.jpg

First Mod...If only I had known what my wallet was in for! :lulz:
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_4532.jpg

Engine out.
http://northcoastturbosystems.com/images/xrt8/aIMG_0226.JPG

New Custom Built Forged Engine.
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/Engine012.jpg
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG00081.jpg
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG00087.jpg

Turbo.
http://northcoastturbosystems.com/images/xrt8/IMG_0283.JPG
http://northcoastturbosystems.com/images/xrt8/IMG_0284.JPG
http://northcoastturbosystems.com/images/xrt8/IMG_0286.JPG

Gauges.
http://northcoastturbosystems.com/images/xrt8/IMG_0293.JPG

Washed with some look good mods.
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0041.jpg

Few more mods
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0202.jpg
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0196.jpg
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0197.jpg

Thanks for looking and a Thank you to BJB for driving all the way to my house to drop off the Hitch!

Escape

[Matt McKenzie]

Welcome aboard! Hmmm, you have a done a little work to that Jeep of yours, LOL!

[Mag 8]

The coolest thing was seeing that you drive your Jeep in the winter with all that expensive plumbing under it!
No road salt there I suppose!

[c love]

Welcome great to have you here. Man you've done that build the right way.
Sick Jeep. What kind of RWHP you getting with that build?

[BJB]

Welcome To MMF.:smiley-linie-010:

Great project you have there. It was nice to get a first hand look at. :I'm watching you:

[StevoSRT]

badass!

[HEMISFEAR]

Welcome to MMF man. Looks like you a have a pistol of a WK there man. Quite the work.

[mikes'ss]

welcome ,,micely modded jeep looks like you will fit rite in here

[BJB]

Those are all very nice pictures, but..... No pictures of the hitch???? :Disappointed_anim:

:pounding table: :ROTFLMAO:

[Vinnysrt8]

welcome looks like a nice build

[Dr.Steve]

great looking rig, lots of work done, but it begs the question, why not just buy the SRT8 and turbo that? Anyhow, welcome aboard and enjoy the fun!!!!!!

[markus]

nice converstion!

[paxton]

Welcome to MMF. Looks like you've got quite alot of time and money in your ride! I like the conversion to the looks of the SRT8!

[Escape]

Welcome aboard! Hmmm, you have a done a little work to that Jeep of yours, LOL!

Thanks Matt..Get home soon man! Stay safe and gods speed!


The coolest thing was seeing that you drive your Jeep in the winter with all that expensive plumbing under it!
No road salt there I suppose!

We have tons of salt here is Michigan, but the plumbing is all 304H Stainless Steel so no worries there and I wash it alot. She should be alot of fun this winter in the snow! I'll probably turn off the boost and run a 3psi spring in the wastegate though just to be a bit snow friendly.


Welcome great to have you here. Man you've done that build the right way.
Sick Jeep. What kind of RWHP you getting with that build?

Thanks man! No numbers as of yet still lots to do! This spring should be awesome.


Welcome To MMF.:smiley-linie-010:

Great project you have there. It was nice to get a first hand look at. :I'm watching you:

Thanks Brian! Stop by anytime...We will have to get a meet going or something.


badass!

Thanks man


Welcome to MMF man. Looks like you a have a pistol of a WK there man. Quite the work.

Thanks, glad to be here. 9 month so far and still more to go...if it's ever done, but don't tell my wife...she thinks it done already! :hehe3: :pounding table:


welcome ,,micely modded jeep looks like you will fit rite in here

Thanks man!


Those are all very nice pictures, but..... No pictures of the hitch???? :Disappointed_anim:

:pounding table: :ROTFLMAO:

:pounding table: It's on there now. I just have to go wash it up! :thumbsup:


welcome looks like a nice build

Thanks Vinny, got that Vortec on there yet?


great looking rig, lots of work done, but it begs the question, why not just buy the SRT8 and turbo that? Anyhow, welcome aboard and enjoy the fun!!!!!!

Thanks man,

Well the engine was going to be ripped out no matter what because of the cast parts that couldn't meet my goals (piston ringlands, rods, cylinder wall thickness, high compression, ect).

I like the 5.7 driveline and would have to by all that if I went with the SRT8. The NV245 transfer case is bulletproof and has a 48/52 split (no spin it just chirps and goes). So far the 5.7 driveline (stage 3 trans) has withstood pushing a 5,100 lb Superbee Ram down the 1/4 @ 11.29 @ 115.77 MPH. With a 60ft. - 1.521 seconds. The Electronic Limited Slips Diffs front and rear lock instantly when floored and plus people just think it's a regular Jeep with a SRT8 body kit, so it's kinda a sleeper till I step into the gas and then it sounds like a 747 Jet.

But the biggest reason of them all....It was easy to talk the wife into! Although I have had to redo most of my house to keep the peace...you know...get some Rims and buy a couch too, new bumper and refinish the bathroom, it goes on and on! :ROTFLMAO:

-------------------------

Thanks guys for the warm welcome and Brian I'll get you some pics of the hitch soon. :thumbsup::hehe3:

Escape

[Johnny--2k]

Very nice! Welcome aboard, you should fit right in here!

[Escape]

After tearing it apart this weekend she was kinda dirty so I washed her up today.
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0361.jpg


Those are all very nice pictures, but..... No pictures of the hitch???? :Disappointed_anim:

:pounding table: :ROTFLMAO:

Here's one of the hitch too...Thanks man! :thumbsup:

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0363.jpg

Soon to have this put on the back.
http://i82.photobucket.com/albums/j243/badass91hatch/027.jpg
http://i82.photobucket.com/albums/j243/badass91hatch/028.jpg
http://i82.photobucket.com/albums/j243/badass91hatch/029.jpg

Now I just need to find someone close with a mandrel bender and the tools to weld with some 304H SS. I checked a bunch of local shops :rolleyes: and nothing so I'll probably be making a trip back down to NCTS to get her all setup. :thumbsup:

And yes my yard is a mess right now! :pounding table: I got tired of tree sap :mad1: and leaves so I cut a bunch of 90' monsters down...plus no more tree limbs falling on my vehicles. :thumbsup:

Escape

[BJB]

That's the photo I was looking for!! Wow, you don't mess around. Nice work!!

[SRTLUVR]

Nice work dude!!!! Shitfire!! Welcome to MMF!!!! :headbang

[Johnny--2k]

Nice work dude!!!! Shitfire!! Welcome to MMF!!!! :headbang

WTF is "shitfire" :ROTFLMAO:


Edit: Nevermind....I found it :hehe3:


1. shitfire

A general exclamation denoting surprise, arousal, discontent, or boredom. It's a buffer word. Earliest film reference is Deliverance, starring uber-fit Burt Reynolds.
Damn, you can play that solo. Shitfire!

That guy just cut me off! SHITFIRE!

Shitfire, I'm bored.

Shitfire, you're sexy.



2. Shitfire

A name given to the Windsor Spitfires hockey team when they are playing like shit (which is most of the time).

"Do you want to watch the Shitfire game?"



3. Shitfire

A derogatory term used to refer to the Crossfire Injection system, used by General Motors between 1981 and 1984. It was replaced by TPI in 1985. Crossfire Injection had a reputation for being unreliable. Also see Ceasefire.
My shitfire Corvette doesn't run.

[Escape]

:hehe3: @ Shitfire! :ROTFLMAO:

Thanks guys!

Just updated the Trinity and it now works in my Jeep! :thumbsup:

All I did for now is mod the stock tune.

Upped the idle for the cam 150, removed the rev limiter in D and removed the top speed limiter. :thumbsup:

Anyone know what is in the canned 93 tune? What perimeters have been modified/changed?

[Grip Grip]

Welcome to the forum. I recall reading about your build over on the JU forum. Nice build.

[imsexyss]

:thumbsup:I am impressed, at the fact you worked at making the Wife happy too, beautifully done...Oh and the Jeep....WOW. Welcome!:D

[Escape]

:thumbsup:I am impressed, at the fact you worked at making the Wife happy too, beautifully done...Oh and the Jeep....WOW. Welcome!:D

Thank you! Gotta keep the homefront happy you know, that way when I get a new mod nothing can be said!

There is a method to my madness :thumbsup:

Gibson F section arrived today and also ordered my rear fog wiring harness, should be here this coming week!

[BJB]

Thank you! Gotta keep the homefront happy you know, that way when I get a new mod nothing can be said!

There is a method to my madness :thumbsup:

Gibson F section arrived today and also ordered my rear fog wiring harness, should be here this coming week!

What did that cost you?? A new couch and kitchen counter tops?? :pounding table: :ROTFLMAO: :tongueout:

[Escape]

What did that cost you?? A new couch and kitchen counter tops?? :pounding table: :ROTFLMAO: :tongueout:

http://www.haskell-dowland.com/content/binary/ROFLMAO.gif

Close, No reminding her about the counter tops either! :lulz: I still have to get my trans and fuel system.

[imsexyss]

Now guys listen to this guy you can get what you want no hassels if you please your Woman too.Not just in stuff, but in bed too.:obscene:

[dynosteve]

welcome mate and great looking jeep you have there

[Escape]

Now guys listen to this guy you can get what you want no hassels if you please your Woman too.Not just in stuff, but in bed too.:obscene:

That's the plan! :obscene::lick:focking

[Escape]

welcome mate and great looking jeep you have there

Thanks Steve!

[Escape]

Now guys listen to this guy you can get what you want no hassels if you please your Woman too.Not just in stuff, but in bed too.:obscene:

This also begs the question...

What does imsexyss do for her mods? :pounding table:

[mikes'ss]

she mods the house ,i mod the cars ,but i am a contractor so i get to do double the work, but also it double's the pleasure:pounding table::obscene:

[Escape]

she mods the house ,i mod the cars ,but i am a contractor so i get to do double the work, but also it double's the pleasure:pounding table::obscene:

Sounds like me, except I get to mod the house, yard, Jeep...everything!

and when it's all said and done I look like this..:dur: sometimes like this too! :bricks1:

:ROTFLMAO:

[imsexyss]

It turns me on to see Mike working on the house, I mean really...I don't know what it is but if he did more around here he'd be walking bold-legged from all the B.J's he'd get:obscene:

[mikes'ss]

oh ya ?

[UJOKIN2]

Well welcome ... its always nice to see a turbo around these parts !

[Escape]

It turns me on to see Mike working on the house, I mean really...I don't know what it is but if he did more around here he'd be walking bold-legged from all the B.J's he'd get:obscene:

:pounding table:Guess we all know Mike just went out to the garage to get some tools to fix something around the house! :bj:


oh ya ?

Hey Mike while your fixing some stuff break some shit to...so you will have more to fix tomorrow! :thumbsup: :pounding table:


Well welcome ... its always nice to see a turbo around these parts !

Thanks Man!

Sweet N/A times and nice TT Challenger too! :thumbsup: :hatoff

[DevssrT]

Welcoem From Long ISland, NY!...thats one hell of a build!...Thanks for joining!

[mikes'ss]

:pounding table:Guess we all know Mike just went out to the garage to get some tools to fix something around the house! :bj:



Hey Mike while your fixing some stuff break some shit to...so you will have more to fix tomorrow! :thumbsup: :pounding table:



Thanks Man!

Sweet N/A times and nice TT Challenger too! :thumbsup: :hatoff



ya thats why shit never gets done around here :hehe3:

[imsexyss]

He is a freaking Liar , I take care of him, Idiot...:mad1: O.k. if he doesnt want to do things around here then I'll soon have a vacancy here. any takers?

[Escape]

Went and did a bit more tuning down at North Coast Turbo Systems this weekend. Got the new exhaust welded up and soon to be running 12 psi's and then with a new fuel system and trans will be pushing up more and more!

Also created a new sig too.

[mikes'ss]

Went and did a bit more tuning down at North Coast Turbo Systems this weekend. Got the new exhaust welded up and soon to be running 12 psi's and then with a new fuel system and trans will be pushing up more and more!

Also created a new sig too.

looks good son

[imsexyss]

Sounds like someone just married their car..hahaha

[Escape]

I made a little video for you guys today and please ignore what the radio is playing when she first starts up...lol.

I take her up to a little over half throttle at the end too...45-95 in a less than 3 seconds! The rest of the vid is just normal driving and I'm usually letting off the throttle as it really wants to go FAST....

She is currently running around 7-8psi at a 9:1 compression. As soon as I run some datalogs with some new files that Tim has sent me we will be pushing her up to 12+ psi and then I have to do some more mods to go up to 20 which will be insane to say the least.

I'll make some more vids in a little bit. I need to find a camera man and a nice clear road.

Enjoy!

<embed width="600" height="361" type="application/x-shockwave-flash" allowFullscreen="true" allowNetworking="all" wmode="transparent" src="http://static.photobucket.com/player.swf?file=http://vid41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/AshortdriveintheJeep.flv">

[BJB]

Sweet Video!! Glad you were able to get out before the shitty weather arrived!

[mikes'ss]

no workie

[BJB]

no workie

Listen Mr....

http://vid41.photobucket.com/albums/e295/My_Kiddos/JAMES STUFF/th_AshortdriveintheJeep.jpg?videoplayer=offsite?vi deoplayer=offsite (http://s41.photobucket.com/albums/e295/My_Kiddos/JAMES STUFF/?action=view&current=AshortdriveintheJeep.flv)

[BJB]

Or try this...

http://s41.photobucket.com/albums/e295/My_Kiddos/JAMES STUFF/?action=view&current=AshortdriveintheJeep.flv

[08 wkjeep5.7]

welcome !

[Escape]

I was just wondering if any of you fellow gear heads out there have ever ran SPA Technique gauges?

I looked for an AutoMeter dual EGT Gauge and it appears that they don't make one.

I have found some made by Spa Technique. Have any of you heard of this company before, thoughts/opinions on their stuff? They are definitely a bit pricey...lol.

Here are the gauges I'm thinking of:

Dual EGT gauge and kit DG 222
http://www.spatechnique.com/product_...ils.cfm?id=385

Dual Boost/Fuel Pressure gauge DG 216
http://www.spatechnique.com/product_...ils.cfm?id=381

I'm thinking Black bezel, black face and a red back light.

Here is what else I have going on......

New fuel system I'm spec'ing out right now, soon to be installed mid-march along with everything else.

Aeromotive In-Line Fuel Filter with Shut-Off Valve #027-12332 - Black in color #12AN 100 micron
http://www.jegs.com/i/Aeromotive/027...ductId=1020033

Aeromotive EFI HP Marine Eliminator Fuel Pump #027-11110 - Black in color #12AN to #10AN
http://www.jegs.com/i/Aeromotive/027...oductId=750073

Aeromotive Billet Fuel Pump Speed Controller #027-16306 - Black in color
http://www.jegs.com/i/Aeromotive/027/16306/10002/-1

Aeromotive In-Line Fuel Filter #027-12306 - Black in color #10 AN 10 micron
http://www.jegs.com/i/Aeromotive/027...oductId=750079

Aeromotive High Flow "Y" Block #027-15620 - Black in color #10 AN to #8 AN
http://www.jegs.com/i/Aeromotive/027/15620/10002/-1

Aeromotive 5.7/6.1L HEMI Fuel Rails #14146 - Red in color
http://aeromotiveinc.com/products-pa...fuel-rail-kit/

Aeromotive A1000 Injected Bypass Regulator #13114 - Black in color
Adjustable from 30 to 70 PSI. Two -10 AN inlet and one -6 AN return ports. http://www.jegs.com/i/Aeromotive/027/13114/10002/-1

Aeromotive Fuel Pressure Gauge #15633 - 1/8" NPT Fitting 0-100PSI
http://www.jegs.com/i/Aeromotive/027...oductId=761355

And a Stage 3 545RFE trans and Stage 3 valve body from SharaDon Performance.
http://www.sharadon.com/

I will be headed up to Sharadon in mid-march for the install of my new trans, fuel system and long tubes.

Once completed she will be dyno tuned for 20+ psi's

Look what UPS brought to me today.

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0684.jpg
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0682.jpg
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0686.jpg
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0685.jpg

Some Custom AR Headers!

Now I just need to get my new SPA Technique dual EGT gauge and tap the headers for the probe in each collector and then get them JetHot coated.

Ordered a set of Nitto Invo's in the 275/315 setup. They should hold traction better than these GY Eagle RS-A runflats

Also adding some customized SRT8 engine half covers and some more stuff in the works...Hurry up Spring!

[paxton]

Lookin' good!!! So what's your wife getting next!:hehe3:

[Escape]

Lookin' good!!! So what's your wife getting next!:hehe3:

Good call! I've already pre-paid her for this years round of mods.:hehe3: :pounding table:

Her silence is awesome! :yeah

[08srt8Calgary]

Your ride is absolutely deadly brother- than turbo spooling up would make me forget that I was in shit with my wife for buyin it.

[Escape]

Thanks everyone!

Today my 275/315 Nitto Invo's arrived. They are currently sitting in the garage awaiting the spring thaw.

I am also doing the 05-06 ignition swap (using MSD coils) to get rid of that rats nest of over the manifold wires.

I ordered all these parts today to do the swap.

Coil Harness 05019952AA
http://public.bay.livefilestore.com/y1pJyw7Xz_dHmMck3mBOcQ63TJ5W-pFyXL8iDj3y5JOp5EYdS-k48qWUforCD1D5u9tgFapEauFgcgiZ6Gpg2DW7Q/HPIM2800.jpg

Composite Valve Covers 05037531AC (I already have the half covers, the 6.1 will be shaved and it will be painted and say HEMI Turbo)
http://img.photobucket.com/albums/v247/GTSfanatic/DSC00344.jpg

Ball Studs 06507366AA
http://img.photobucket.com/albums/v247/GTSfanatic/DSC00303.jpg
http://img.photobucket.com/albums/v247/GTSfanatic/DSC00304-1.jpg

MSD Blaster Coils 82558
http://www.latemodelrestoration.com/Content/Images/ProductImages/Medium/msd-82558.JPG

I plan on shaving the intake manifold and having it all painted up too.
http://i232.photobucket.com/albums/ee105/phallohmetoo/Intake%20Manifolds/November2009073.jpg

Hurry up spring time!

[mikes'ss]

badass

[Kasser]

Damn nice painting job!

[Escape]

Thanks guys!

Here's some more mods with pics.

Nitto INVO's 275/315 Combo to hopefully keep this thing stuck to the ground.

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0702.jpg

So I got sick of all the over the top wiring (pic below) and plus I upgraded the ignition while I was at it. Here is what I started with...The ugly embarrassing 05 rats nest of wires. Only 8 shared coils, spark plug wires over the manifold. Basically a ugly underpowered design.

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0694.jpg

New stuff awaiting install.

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0763.jpg

First order of business. Get rid of those over the top spark plug wires, shared coils and those huge ball socket cover attachments.

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0764.jpg
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0765.jpg
http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0767.jpg

Next order of business. The 05 to 06 coil connections are different and wired totally opposite. Cut those off and rewire them to the 06 specs.

Cut, striped, crimped, soldered and shrink wrapped! Orange is Coil Command. Purple is ASD Relay.

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0769.jpg

Once your all done rewiring the ignition, as if that wasn't enough fun for you, now remove the valve covers.

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0770.jpg

Now put the new valve covers and coil packs on. Reattach all wiring and hoses.

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0772.jpg

Now trim to fit your engine half covers, Wipe up all the blood you dripped all over, get some cold packs for your knees (kneeling on a battery and fender for hours hurts A LOT), a heating pad for your back that is killing you, turn down the radio (cause your not cussing out the engineers anymore who thought it was cool to put all the bolts in unreachable places) and admire your work as you turn the key and she starts right up and roars like the savage beast this HEMI is! :yeah

Now if there wasn't 3 feet of snow outside I'd take her for a spin.

http://i41.photobucket.com/albums/e295/My_Kiddos/JAMES%20STUFF/IMG_0775.jpg

Also just send out the check for my SharaDon Stage 3 Transmission.

20+ psi, 1,000 horse, 10 sec Jeep make it or break it here I come... :nuts: